The shaft shown in the figure below receives P hp from a wind turbine output sha
ID: 2327109 • Letter: T
Question
The shaft shown in the figure below receives P hp from a wind turbine output shaft through a V-belt sheave at point C. The gear pair at E delivers P_1 hp to an electric generator. The V belt sheave at A delivers P_2 to a bucket elevator to carry food grains. The shaft rotate at N rpm. The sheavs and gear are located axially by retaining rings. Assume suitable key sets to relain the sheaves and gear on the the shaft. Use AISI 1050 cold drawn steel for the shaft. Compute the minimum expectable diameters D_1 through D_2 as explained in the figure. Assume P = (100 + x + y)hp P_1 = (65 + y)hp P_2 = (P + P_1)hp N = (1500 + 10X+ Y)rpm Orientation of elements A, C, and E as viewed from right end of by shaft.Explanation / Answer
solution:
1)here design of shaft of diameter D2
power=P2=41*746=(F1-F2)*V
we get,D=L=.1524 m
F1-F2=2446.07 N
where for v belt with 180 wrap angle and groove angle 35 degree force ratio is 2.56
F1=2.56F2
on putting we get
F2=1567.99 N
F1=4014.06 N
torque is=T=(F1-F2)*.1524/2=186.39 Nm
for ces in vertical and horizontal plane are
Fv1=F1sin60=1357.9 n
Fv2=F2sin60=3476.27 N
Frv=4834.18 N
Fh1=F1cos60=783.9 N
Fh2=f2cos60=2007.03 N
Frh=2791.02 N
bending moment in vertiacal and horizontal plane is
Mv=Frv*L=736.72 Nm
Mh=Frh*L=425.35 Nm
M=850.7 Nm
equavalent torque
Te=((KbM)^2+(KtT)^2)^.5
Kb=1.5
Kt=1
we get Te=1289.59 Nm
t allowable=.18 Sut
Sut=790 N/mm2
t all=.18*Sut=142.2
but reduction 25%
t all=106.65 N/mm2
by ASME code
Tall=16*te/pi*d^3
D2=15.54 in
2)design for diameter D4
here design of shaft of diameter D4
power=P2=113*746=(F1-F2)*V
we get,D=.2032,L=.1524 m
F3-F4=5056.12 N N
where for v belt with 180 wrap angle and groove angle 35 degree force ratio is 2.56
F3=2.56F4
on putting we get
F4=3241.16 N N
F3=8297.3 N
torque is=T=(F1-F2)*.2032/2=513.71 Nm
for ces in vertical and horizontal plane are
Fv1=F3sin40=2088.37 N
Fv2=F4sin40=5333.4 N
Frv=7415.4 N
Fh1=F3cos40=2482.87 N
Fh2=f4cos40=6356.1 N
Frh=8838.97 N
where reaction at B and D in vertical and horizontal plane are
Rbv=Rdv=3707.7 N
Rbh=Rdh=4419.48 N
Rbr=Rdr=5768.78 N
M=Rbr*L=879.16 Nm
equavalent torque
Te=((KbM)^2+(KtT)^2)^.5
Kb=1.5
Kt=1
we get Te=1415.26 Nm
t allowable=.18 Sut
Sut=790 N/mm2
t all=.18*Sut=142.2
but reduction 25%
t all=106.65 N/mm2
by ASME code
Tall=16*te/pi*d^3
D4=16.03 in
2)design for diameter D6
1)here design of shaft of diameter D6
power=P1=72*746=T*pi*2*N/60
torque is=T=P/w=327.32 Nm
for ces in tangential and radial direction are
Ft=T*2/D=2147.76 N
Fr=Fttan20=781.72 N
f=(Ft^2+Fr^2)^.5
M=F*L=348.32 Nm
M=348.32 Nm
equavalent torque
Te=((KbM)^2+(KtT)^2)^.5
Kb=1.5
Kt=1
we get Te=616.54 Nm
t allowable=.18 Sut
Sut=790 N/mm2
t all=.18*Sut=142.2
but reduction 25%
t all=106.65 N/mm2
by ASME code
Tall=16*te/pi*d^3
D6=12.15 in
Related Questions
drjack9650@gmail.com
Navigate
Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.