Question 1. 1. (TCO 3) This network appears to be working most of the time but l

Question

Question 1.1. (TCO 3) This network appears to be working most of the time but lately it becomes slower and slower as new end devices and applications come online. What is the characteristic that is violated? (Points : 2)        Security
       Availability
       Reliability
       Manageability
       Scalability


Pool 2 – 5:1; 2 points; address TCO 3
Type: MC Question 2.2. (TCO 3) Routers use the routing table to _____. (Points : 2)        select the best path toward the destination
       encapsulate layer 3 packets before they are sent to the egress interface
       determine the way of reaching the host on the ingress interface
       exchange network reachability information with each other
       C and D

Type: MC Question 3.3. (TCO 3) What happens next if a router determines that an incoming packet has a destination of a directly connected network? (Points : 2)        Check the ARP cache and forward packet to local host.
       Check the routing table for lowest cost path.
       Drop the packet and send a control message to the source address.
       Encapsulate the packet into a destination IP address before forwarding.
       Forward the packet to the next hop.

Type: MC Question 4.4. (TCO 3) The arrangement of the cables, network devices, and end systems in a network is called its _____. (Points : 2)        logical topology
       logical network overlay
       physical topology
       configuration topology
       None of the above

Type: MC Question 5.5. (TCO 3) Being able to use a single physical router interface to route traffic between multiple VLANs on a network is called _____. (Points : 2)        hub and spoke router
       sub-interface VLAN routing
       composite VLAN routing
       trunk-safe router
       router-on-a-stick

Type: MC Question 6.6. (TCO 3) What is a disadvantage of traditional routing? (Points : 2)        Does not support mutli-hop routing
       Can create layer-two loops
       Transport too many VLAN-tagged packets
       Can create layer 3 routing loops
       All of the above

Type: MC Question 7.7. (TCO 3) The command used on a Cisco Catalyst 2960 switch to change the switched database manager (SDM) template is _____. (Points : 2)        sdm change
       sdm use
       sdm prefer
       sdm enable
       None of the above


Pool 9 – 3:1; 2 points; address TCO 3
Type: MC Question 8.8. (TCO 3) Which of the following is the proper format for assigning an IPv4 address to the interface on a Cisco router? @ See Chapter 4, page 175. (Points : 2)        ip address ip-address subnet-mask
       ip address ip-address
       assign address ip-address subnet-mask
       interface ip-address
       None of the above

Type: MC Question 9.9. (TCO 3) Which command would you use to troubleshoot a routing problem between a router and a switch? (Points : 2)        show interface ip brief
       debug ip route
       Debug interface ip
       show ip protocols
       show ip route
Question 1.1. (TCO 3) This network appears to be working most of the time but lately it becomes slower and slower as new end devices and applications come online. What is the characteristic that is violated? (Points : 2)        Security
       Availability
       Reliability
       Manageability
       Scalability


Pool 2 – 5:1; 2 points; address TCO 3
Type: MC Question 2.2. (TCO 3) Routers use the routing table to _____. (Points : 2)        select the best path toward the destination
       encapsulate layer 3 packets before they are sent to the egress interface
       determine the way of reaching the host on the ingress interface
       exchange network reachability information with each other
       C and D

Type: MC Question 3.3. (TCO 3) What happens next if a router determines that an incoming packet has a destination of a directly connected network? (Points : 2)        Check the ARP cache and forward packet to local host.
       Check the routing table for lowest cost path.
       Drop the packet and send a control message to the source address.
       Encapsulate the packet into a destination IP address before forwarding.
       Forward the packet to the next hop.

Type: MC Question 4.4. (TCO 3) The arrangement of the cables, network devices, and end systems in a network is called its _____. (Points : 2)        logical topology
       logical network overlay
       physical topology
       configuration topology
       None of the above

Type: MC Question 5.5. (TCO 3) Being able to use a single physical router interface to route traffic between multiple VLANs on a network is called _____. (Points : 2)        hub and spoke router
       sub-interface VLAN routing
       composite VLAN routing
       trunk-safe router
       router-on-a-stick

Type: MC Question 6.6. (TCO 3) What is a disadvantage of traditional routing? (Points : 2)        Does not support mutli-hop routing
       Can create layer-two loops
       Transport too many VLAN-tagged packets
       Can create layer 3 routing loops
       All of the above

Type: MC Question 7.7. (TCO 3) The command used on a Cisco Catalyst 2960 switch to change the switched database manager (SDM) template is _____. (Points : 2)        sdm change
       sdm use
       sdm prefer
       sdm enable
       None of the above


Pool 9 – 3:1; 2 points; address TCO 3
Type: MC Question 8.8. (TCO 3) Which of the following is the proper format for assigning an IPv4 address to the interface on a Cisco router? @ See Chapter 4, page 175. (Points : 2)        ip address ip-address subnet-mask
       ip address ip-address
       assign address ip-address subnet-mask
       interface ip-address
       None of the above

Type: MC Question 9.9. (TCO 3) Which command would you use to troubleshoot a routing problem between a router and a switch? (Points : 2)        show interface ip brief
       debug ip route
       Debug interface ip
       show ip protocols
       show ip route

Explanation / Answer

1) option C .reliability

2) option A select best path towards destination

3) option A check ARP cache and forward the packet

4) option E none of the above

5) option B sub interface vlan routing

6) option E all of above

7) option C

8)option C

9) option C debug interface ip

Related Questions

Navigate

• Browse (All)
• Browse Q
• Subjects

---

---

Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.