Short Answer 1. Write C code to setup PORTB in the following configuration. Do n

Question

Short Answer 1. Write C code to setup PORTB in the following configuration. Do not write an entire C program configuration: , only write the lines required to perform the following PB7 through PB4 are inputs with internal pull up resistors enabled and PB3 through PBO are outputs and set to logic high (5 Points) Write a while loop that executes and continues executing as long as PB3 is logic low. Assume the PB3 has previously been configured as an input with pull-up resistor enabled. (5 Points) 2.

Explanation / Answer

#ifndef COMDATA_H
#define COMDATA_H
const int THOSNDS=1000;
const int HUNDRDS=100;
const int TENS=10;
struct ComData
{
string zip;
string date;
string comName;
string city;
string state;
string street;
  
};

#endif /* COMDATA_H */

#ifndef EMPDATA_H
#define EMPDATA_H
struct EmpData
{
string empName;
float hrsWrkd;
float payRate;
};

#endif /* EMPDATA_H */

-----------------------------------------------------------------------------

MAIN PROGRAM

cout<<"Pay Checks"<<endl<<endl;
ComData company;
EmpData worker;
int size=0;
EmpData *worList;

//Input data on the company
cout<<"Please enter the necessary information to fill out a check."
<<endl;
cout<<"Which company is this payroll for?"<<endl;
getline (cin, company.comName);
cout<<"Enter the street address of company:"<<endl;
getline (cin, company.street);
cout<<"Enter the city:"<<endl;
getline(cin, company.city);
cout<<"Enter the state:"<<endl;
getline (cin, company.state);
cout<<"Enter company zipcode:"<<endl;
getline (cin, company.zip);
cout<<"Enter the date this payrole is to be paid:"<<endl;
getline (cin, company.date);

//Input first round of employee data.
//MUST enter data for at least one employee
cout<<"Enter the employee's name: "<<endl;
getline(cin, worker.empName);
cout<<"Enter the hours worked this week (Max of 80):"<<endl;
cin>>worker.hrsWrkd;
//validate data type and range
while (cin.fail() || worker.hrsWrkd>80 || worker.hrsWrkd<=0)
{ //validate data type and range
cout<<"Entry not valid! Enter a non-zero positive integer less than 80!"
<<endl;
cin.clear();
cin.ignore(256, ' ');
cin>>worker.hrsWrkd;
}
cout<<"Enter the rate of pay for this employee (Max of $133/hr) "
"(0 or less to exit):"<<endl;
cin>>worker.payRate;
//validate data type and range
while (cin.fail() || worker.payRate>133 || worker.payRate<=0)
{
cout<<"Entry not valid! Enter a non-zero positive integer of 133 or "
"less!"<<endl;
cin.clear();
cin.ignore(256, ' ');
cin>>worker.payRate;
}
size++;
while (worker.hrsWrkd >0 && worker.payRate>0)
{
prnChck(worker, company);
cout<<endl;
worList=addline(worList, worker, size);

//Repeat process until a check for $0 or less would be cut
cout<<"Enter the employee's name: "<<endl;
cin.ignore(256, ' ');
getline(cin, worker.empName);
cout<<"Enter the hours worked this week (Max of 80) (0 or less to exit)"
":"<<endl;
cin>>worker.hrsWrkd;
//validate range and data type
while (cin.fail() || worker.hrsWrkd>80)
{
cout<<"Entry not valid! Enter a non-zero positive integer less "
"than 80!"<<endl;
cin.clear();
cin.ignore(256, ' ');
cin>>worker.hrsWrkd;
}
cout<<"Enter the rate of pay for this employee (Max of $133/hr):"<<endl;
cin>>worker.payRate;
//validate range and data type
while (cin.fail() || worker.payRate>133)
{
cout<<"Entry not valid! Enter a non-zero positive integer of "
"133 or less!"<<endl;
cin.clear();
cin.ignore(256, ' ');
cin>>worker.payRate;
}
size++;
}
pEmpCon(worList, size);
delete [] worList;
}

Related Questions

Navigate

• Browse (All)
• Browse S
• Subjects

---

---

Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.